For example, if your router assigns DHCP addresses in the range of 192.168.2.100 to 192.168.2.254, then you could try statically assign your camera to something under 192.168.2.100, i.e. If power goes out and your router and/or camera reboots, it will be assigned the same address (i.e netgear router: How do I reserve an IP address on my NETGEAR router? | Answer | NETGEAR Support).Ģ) Check your router and see what address range is used to connect your devices. If your router is using DHCP to assign IP addresses to your network devices, you have a couple options:ġ) Check the MAC address of the camera (see if it's on the label, something like 76:00:B3:E5:0F), then in the router, use the MAC address to assign a 192.168.2.xxx IP address to it, this will reserve this address. Then change your computer back to auto assign IP address, and connect the cam and computer to your router. Then access it via the web browser interface (192.168.1.108) and change it to either DHCP and let your router assign a IP address (you can reserve an IP address in your router, see below), or modify the static IP address to your 192.168.2.xxx range. Your router is a DHCP server, unless you have done some super fancy networking configuration, but I’m guessing by your questioning that this is not the case.Ĭlick to expand.Another way to change your camera address, change your address of your computer to a static address, something like 192.168.1.100 ( ) and connect your computer directly to the camera with a network cable. After you’ve set it, you can then plug it directly into your router and you should be able to access it via the IP you assigned from any device within your network.ġ69. is the standard IP address assigned to an Ethernet card in Windows when it’s not hooked up to a DHCP server. But you can assign whatever you want as long as it’s not already taken by another device. ![]() In my network environment I have mine all set with static IP addresses ranging from. For sake of simplicity, if you can get to the webpage of the camera, I would configure it to a set IP address of 192.168.2.something. Your router is a DHCP server, unless you have done some super fancy networking configuration, but I’m guessing by your questioning that this is not the case.Īre you planning to hook the camera directly into your router via an Ethernet cable? If so, your router will be serving out DHCP assigned IP addresses on the 192.168.2 subnet regardless of whether it’s a wireless or physically connected device. ![]() In otherwords, your IP needs to be 192.168.1.x to connect to the 192.168.1.108 default address, unless your router specifically has a route setup between the 192.168.2 subnet and the 192.168.1 subnet which I'm guessing it doesn't.Ĭlick to expand. is the standard IP address assigned to an Ethernet card in Windows when it’s not hooked up to a DHCP server. You need to be on the same subnet as the camera when configuring it. You can pick up used / beat up M4600s (just make sure they have an i7 in them) for pretty cheap nowadays off ebay. I have a 4TB WD Purple drive hooked to it via USB 3.0, with a 2TB internal SSD, 32 GB Ram, It runs an i7 processor and it's running 5 cameras at the moment (i have 3 more to hook up) + Runs a Plex Media Server, and 2 VMs all at the same time. If you're running outdoor security cameras, I find this the easiest method.Īlso, anyone else looking for good blue iris server options. From the switch, I run a single ethernet cable to each camera which is all that's needed to have it powered, but I had to configure each camera ahead of time so that it would be setup for the network. once it's initialized you can change the camera's IP address in the configuration page to 192.168.2.whatever you want, and plug it into the router where it should work.įor me, I've setup a CISCO SG500-28P (PoE commercial switch) rack mounted in the attic with ventilation, with a dedicated 10G trunk run down to my wiring closet where I keep my main router that it plugs into. ![]() just plug the camera directly into a laptop or computer with an ethernet port directly (make sure it's powered), change your IP address to 192.168.1.2, subnet mask 255.255.255.0, and leave the rest blank. In otherwords, your IP needs to be 192.168.1.x to connect to the 192.168.1.108 default address, unless your router specifically has a route setup between the 192.168.2 subnet and the 192.168.1 subnet which I'm guessing it doesn't.Įasiest way. ![]() Click to expand.You need to be on the same subnet as the camera when configuring it.
0 Comments
Leave a Reply. |